Français

Lessons · Lesson E1 · Electricity basics · 10 min

Voltage, current, resistance

Three ideas, one rule. About 10 minutes, with one slider to play with.

Why does a bulb light up?

Connect a battery to a small bulb with wires and it lights. Cut one wire and it goes dark. Something has to travel all the way around a loop, starting and ending at the same place. We call that loop a circuit [1].

Simple LED circuit A 5 V supply (USB), a closed switch, a 220 ohm resistor and a red LED connected in one loop. Arrows show conventional current leaving the supply's plus terminal, going through the switch, resistor and LED, and returning to the minus terminal. About 14 milliamps flow. FIG. 1 — SIMPLE LED CIRCUIT5 V supply (USB)Switch (closed)Resistor220 ΩLED (red)drop ≈ 2 VIII = (5 V − 2 V) ÷ 220 Ω ≈ 14 mAConventional current (I): out of +, round the loop, back to −.Electrons really drift the other way (− to +). Same maths.Ohm's law applies to the resistor: it gets 5 V − 2 V = 3 V.
Tap the diagram to open it full screen.

Three ideas explain almost everything about it: voltage, current and resistance.

Watch the 3-minute explainer · Download the video in 1080p (18.3 MB)

Voltage: the push

Voltage (symbol V, unit: the volt) is the difference in electrical “push” between two points [2][3]. A battery has two ends, and the difference between them is what drives the charges around the loop [1]. A bigger difference is a bigger push.

The water picture. Picture a pump in a closed loop of pipes. Voltage is like the pressure the pump creates between its outlet and its inlet [2][3].

Where the picture stops. A cut pipe spills water on the floor. A cut wire spills nothing: the current simply stops [1]. And charges are not used up on the way round: in a single loop, the same amount of current passes every point [2].

Water loop analogy A pump pushes water round a closed loop of pipe with a narrow section. The pump is like the supply. The pressure difference it creates, high pressure at its outlet and low pressure at its inlet, is like voltage. The water flow per second is like current, and it is the same everywhere in the loop. The narrow section limits the flow, like a resistor. FIG. 2 — THE WATER ANALOGYPumphighpressurelowpressuresame flow everywhere(closed loop)narrow section1234Where the analogy stops: a cut pipe spills water; a cut wirespills nothing, the current just stops. And charges are notused up: the same amount comes back to the supply.1Pump↔Supply (battery, USB)2Pressure difference↔Voltage V · volts (V)3Water flow (litres/s)↔Current I · amps (A)4Narrow section↔Resistance R · ohms (Ω)
Tap the diagram to open it full screen.

Current: the flow

Current (symbol I, unit: the ampere, or amp, A) tells how much charge passes a point each second. One ampere is one coulomb of charge per second [4]. Small electronics often use thousandths of an amp: 1 mA = 0.001 A [3].

The water picture. Current is like the amount of water going past a spot in the pipe each second [3].

Where the picture stops. The charges themselves drift slowly along a wire, yet a bulb lights the moment you close the switch. The wire is already full of charges, so push one in at one end and another leaves the other end almost at once [5].


Resistance: the squeeze

Resistance (symbol R, unit: the ohm, written Ω) says how much a part holds back the current: for the same voltage, more resistance means less current [3][6]. Wires hold back very little. A resistor is a small part made to hold back a chosen amount [6].

More resistance, less current Two identical circuits with a 5 V supply (USB) and a red LED. Left: a 220 ohm resistor, about 14 milliamps, thick current arrows and a bright LED. Right: a 1 kilo-ohm resistor, 3 milliamps, thin arrows and a dim LED. FIG. 4 — SAME SUPPLY, TWO RESISTORSA · R = 220 Ω5 V220 ΩI ≈ 14 mALED: bright(5 V − 2 V) ÷ 220 ΩB · R = 1 kΩ5 V1 kΩI = 3.0 mALED: dim(5 V − 2 V) ÷ 1000 ΩSame 5 V supply. More resistance → less current → dimmer LED.Arrow thickness shows how much current flows; the resistor symbol keeps the same size.
Tap the diagram to open it full screen.

The water picture. In our pump loop, resistance is a narrow section of pipe: the narrower it is, the less water gets through [3][6].

Where the picture stops. In a resistor, the electrical energy turns into heat, which is why working resistors get warm [5]. And a resistor’s value is not perfectly fixed: all resistors change slightly with temperature, and some parts, such as a thermistor, are made to change a lot [6].


Ohm’s law: how the three fit together

For many parts, the three are linked by one short rule [7]:

V = I × R

Rearranged: I = V ÷ R. More push means more current. More resistance means less current.

Example: 5 V across 1000 Ω gives I = 5 ÷ 1000 = 0.005 A, so 5 mA.

Ohm's law triangle A triangle split into three cells: V on top, I and R at the bottom with a times sign between them. Cover the value you want: V equals I times R, I equals V divided by R, R equals V divided by I. FIG. 3 — OHM'S LAWVIRCover the letter you want:V = I × Rvoltage = current × resistanceI = V ÷ Rcurrent = voltage ÷ resistanceR = V ÷ Iresistance = voltage ÷ currentExample: 3 V across 220 Ω → I = 3 V ÷ 220 Ω ≈ 0.014 A ≈ 14 mAV in volts (V) · I in amps (A) · R in ohms (Ω)
Tap the diagram to open it full screen.

An LED in the loop. An LED is not a resistor. Across its normal working currents, it takes a roughly fixed voltage, about 2 V (often 1.8–2.2 V) for a typical red one; other colours take more or less [8][9]. So with a 5 V supply, 5 − 2 = 3 V is left for the resistor in series with it, and Ohm’s law applies to that resistor: 3 V ÷ 220 Ω = 0.0136 A, about 13.6 mA. This is how you choose a resistor to protect an LED, which is usually kept at or below about 20 mA [8][9].

Turn the resistor Illustrative, not measured.
Turn the resistor: the LED circuit with your values The circuit of figure 1 with the supply and resistor you choose. The current, the LED glow and the thickness of the current arrows follow Ohm’s law applied to the resistor. FIG. 1 — SIMPLE LED CIRCUIT5 V supplySwitch (closed)Resistor220 ΩLED (red)drop ≈ 2 VIII = (5 V − 2 V) ÷ 220 Ω = 13.6 mAConventional current (I): out of +, round the loop, back to −.Electrons really drift the other way (− to +). Same maths.Ohm's law applies to the resistor: it gets 5 V − 2 V = 3 V.

Current I

13.6 mA

I = (5 V − 2 V) ÷ 220 Ω = 13.6 mA

LED: bright · Red LED, fixed drop Vf = 2.0 V

Is this exact?

A real red LED’s drop varies from about 1.8 to 2.2 V with the current and the part, and it is lower at very small currents. This model is rough, but enough to choose a resistor.

Voltage across the resistor, V_R: 3 V
Power in the resistor, P = I² × R: 0.041 W. An ordinary 1/4 W resistor is fine for every setting here.

Limit of the rule. It holds for parts called “ohmic”, such as ordinary resistors. It is not a law of nature for every part [7]. An LED or a diode does not follow it: its current is not proportional to the voltage. For a red LED, below about 1.5 V almost nothing flows, then the current rises very fast; other diodes switch on at other voltages [7].


Check yourself

Three short questions. Nothing is saved, take your time.

  1. You keep the same resistor and double the voltage across it. What happens to the current?

    • It is cut in half
    • It doubles
    • It stays the same
    Show the answer

    It doubles. I = V ÷ R. With R fixed, twice the voltage gives twice the current [7].

  2. A 5 V supply is connected straight across a 1000 Ω resistor. How much current flows?

    • 0.005 A (5 mA)
    • 0.5 A
    • 5000 A
    Show the answer

    0.005 A (5 mA). I = 5 V ÷ 1000 Ω = 0.005 A, which is 5 mA [7].

  3. In the water picture, what does a narrow section of pipe stand for?

    • A higher voltage
    • A higher resistance
    • A bigger battery
    Show the answer

    A higher resistance. A narrow section lets less water through for the same push, like a larger resistance lets less current through [3][6].


Sources

Show the 9 sources
  1. SparkFun, “What is a Circuit?” (a circuit is a closed path; an open circuit does not work; every source has two sides) — https://learn.sparkfun.com/tutorials/what-is-a-circuit
  2. All About Circuits textbook, Volume I (DC), “Voltage and Current” (voltage is relative between two points; pump picture; same current everywhere in a single loop) — https://www.allaboutcircuits.com/textbook/direct-current/chpt-1/voltage-current/
  3. SparkFun, “Voltage, Current, Resistance, and Ohm’s Law” (voltage as a difference between two points; water analogy; narrow hose, less flow; 20 mA = 0.020 A) — https://learn.sparkfun.com/tutorials/voltage-current-resistance-and-ohms-law
  4. OpenStax, University Physics Volume 2, section 9.1 “Electrical Current” (current is the rate of flow of charge; ampere = coulomb per second) — https://openstax.org/books/university-physics-volume-2/pages/9-1-electrical-current
  5. OpenStax, University Physics Volume 2, section 9.2 “Model of Conduction in Metals” (slow drift, fast signal; collisions heat the conductor) — https://openstax.org/books/university-physics-volume-2/pages/9-2-model-of-conduction-in-metals
  6. OpenStax, University Physics Volume 2, section 9.3 “Resistivity and Resistance” (higher resistance, lower current; resistors; temperature dependence, thermistor) — https://openstax.org/books/university-physics-volume-2/pages/9-3-resistivity-and-resistance
  7. OpenStax, University Physics Volume 2, section 9.4 “Ohm’s Law” (V = IR; ohmic and nonohmic parts; diodes; not a law of nature) — https://openstax.org/books/university-physics-volume-2/pages/9-4-ohms-law
  8. SparkFun, “Light-Emitting Diodes (LEDs)” (forward voltage drop; the resistor gets the remaining voltage; 20 mA continuous rating for the example LED) — https://learn.sparkfun.com/tutorials/light-emitting-diodes-leds
  9. SparkFun, “Resistors” (red LED forward voltage around 1.8 V; forward voltage 1.7–3.4 V depending on colour; basic LEDs about 20 mA maximum) — https://learn.sparkfun.com/tutorials/resistors

Video credits: Voice: Kokoro (Apache 2.0 licence). Music: made in-house.

Pinch or double-tap to zoom, swipe to change diagram.Scroll with Ctrl or double-click to zoom. Arrow keys change diagram.