Français

Lessons

Short lessons, 10 to 30 minutes each, to understand what is happening inside the missions. Diagrams first, one idea per screen, three questions at the end. Nothing is saved.

E Electricity basics

  1. E1 10 min · Start here

    Voltage, current, resistance

    Three ideas, one rule. About 10 minutes, with one slider to play with.

  2. E2 15 min

    Your first circuit

    Build a loop on a breadboard, spot a short circuit, and check it with a multimeter. About 15 minutes, with one interactive breadboard.

    Before this lesson: E1 Voltage, current, resistance

  3. E3 15 min

    LEDs and the right resistor

    Which way round an LED goes, and how to pick the resistor that keeps it safe, with one formula and a calculator. About 15 minutes.

    Before this lesson: E2 Your first circuit

  4. E4 20 min

    Power: batteries, 3.3 V and 5 V

    Choose a battery pack, estimate how long it lasts, join the grounds, and feed an ESP32 board the right voltage on the right pin. About 20 minutes, with a battery-life calculator.

    Before this lesson: E1 Voltage, current, resistance, E3 LEDs and the right resistor

  5. E5 20 min

    Series, parallel and the voltage divider

    Combine resistors in a row or side by side, split a voltage in two, and use a light-dependent resistor to let your ESP32 "see" the light. About 20 minutes, with an interactive divider.

    Before this lesson: E1 Voltage, current, resistance, E3 LEDs and the right resistor

K Code basics

  1. K1 30 min

    Your first program: connect and upload code to your ESP32

    From a box of parts to a blinking LED and your first message on screen, one step at a time. About 30 minutes, with a troubleshooting table for when something refuses to work.

    Before this lesson: E3 LEDs and the right resistor

  2. K2 20 min

    Inputs, outputs and if

    Read a button, switch on an LED and a buzzer, and let your code decide what to do. About 20 minutes, with a virtual button to press.

    Before this lesson: K1 Your first program: connect and upload code to your ESP32

  3. K3 25 min

    Analog values and thresholds

    Read a changing voltage with analogRead(), turn it into a decision with a threshold, then stop the stutter with two thresholds. About 25 minutes, with a live graph you can drag.

    Before this lesson: K2 Inputs, outputs and if, E5 Series, parallel and the voltage divider, S1 Light and infrared sensors

  4. K4 30 min

    Timing and states

    Stop the board from freezing during a wait, keep time with millis(), then build a small alarm as a state machine. About 30 minutes, with a diagram you can press.

    Before this lesson: K3 Analog values and thresholds

  5. K5 30 min

    Libraries and modules (I2C, UART)

    Install a library, find out which modules are on your I2C wires with a scanner sketch, and see how a UART link differs. About 30 minutes, with a bus you can press.

    Before this lesson: K4 Timing and states

S Sensors

  1. S1 20 min

    Light and infrared sensors

    Meet your first digital sensor, an infrared break-beam pair that tells your ESP32 whether something is blocking an invisible line. About 20 minutes, with a beam you can break on screen.

    Before this lesson: K2 Inputs, outputs and if, E4 Power: batteries, 3.3 V and 5 V

  2. S2 30 min

    Magnets, tilt and motion

    Build a door alarm around a reed switch and a magnet, try a tilt switch, then read a PIR motion sensor and wire it safely to the ESP32. About 30 minutes, with a magnet you can drag.

    Before this lesson: K2 Inputs, outputs and if

  3. S3 40 min

    Smart sensors, distance and camera

    Measure distance with a time-of-flight sensor, then read where a coloured target sits in a camera module's view. About 40 minutes, with a distance cone and a camera frame you can move.

    Before this lesson: K5 Libraries and modules (I2C, UART), A2 Servos and PWM

M Mechanics and 3D

  1. M1 25 min

    Soldering and perfboard

    Solder safely, tell a good joint from a bad one, and move a breadboard circuit onto a perfboard so it stays put. About 25 minutes, with a practice exercise.

    Before this lesson: E2 Your first circuit

  2. M2 25 min

    3D printing for your projects

    Go from a model to a printed box that fits: measuring, clearance, walls, screw holes, battery bays, overhangs and PLA settings. About 25 minutes, with a clearance slider.

  3. M3 40 min

    Mechanisms: levers, linkages, gears

    See how levers, rods and gears trade distance for force, then use a servo to move a printed flap or latch safely. About 40 minutes, with a gear-ratio widget and a linkage you can drag.

    Before this lesson: A2 Servos and PWM, M2 3D printing for your projects

A Actuators and motors

  1. A1 30 min

    Sound, buzzers and speakers

    Tell an active buzzer from a passive one, play notes and a short melody with tone(), and meet the DFPlayer Mini for MP3 files. About 30 minutes, with a piano you can press.

    Before this lesson: K2 Inputs, outputs and if

  2. A2 35 min

    Servos and PWM

    Understand PWM and duty cycle, then command a servo to an angle with 1 to 2 ms pulses, with its own power supply. About 35 minutes, with a slider you can move.

    Before this lesson: K3 Analog values and thresholds, E4 Power: batteries, 3.3 V and 5 V

  3. A3 35 min

    DC motors and H-bridges

    Understand what an H-bridge does, then make a small DC motor go forward, backward, brake or coast, at the speed you choose, with a DRV8833 board and its own power supply. About 35 minutes, with switches you can click.

    Before this lesson: C2 Transistors, MOSFETs and diodes, A2 Servos and PWM

  4. A4 35 min

    Addressable LEDs

    Light a ring of NeoPixel LEDs from one data pin, mix colours as red, green and blue numbers, and work out how much power the ring needs. About 35 minutes, with a colour mixer you can move.

    Before this lesson: K4 Timing and states, E4 Power: batteries, 3.3 V and 5 V

C Components

  1. C1 25 min

    Capacitors

    Learn what a capacitor stores, how to read its value and its marks, and why a 470 µF one across a servo's power wires helps when the supply dips as the servo moves. About 25 minutes, with a tank you can fill.

    Before this lesson: E4 Power: batteries, 3.3 V and 5 V, A2 Servos and PWM

  2. C2 45 min

    Transistors, MOSFETs and diodes

    Let a tiny signal from your board switch a bigger current: an NPN transistor, a logic-level MOSFET, and the diode that protects them from a motor. About 45 minutes.

    Before this lesson: E4 Power: batteries, 3.3 V and 5 V, K2 Inputs, outputs and if

W Wireless and connected things

  1. W1 45 min

    Wi-Fi and radio (alerts, web pages, board-to-board)

    Join your Wi-Fi without sharing your password, send an alert to your phone, serve a tiny control page, and make two boards talk by radio. About 45 minutes.

    Before this lesson: K4 Timing and states